Westerbeke 38B FOUR Instrukcja Operatora Strona 35
- Strona / 86
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Engine
Break-In
Procedure
Although your generator has experienced a minimum
of
one hour
of
test operations to make sure accurate
assembly procedures were followed and that the generator operated properly, a break-in time is required.
The service life
of
your engine is dependent upon how the engine is operated and serviced during its
iuitial hours
of
use.
Your new engine requires approximately
50 hours
of
initial conditioning operations to break in each
moving part in order to maximize the performance and service life
of
the engine. Perform this
conditioning carefully, keeping
in
mind the following:
1.
Start the generator according to the "STARTING PROCEDURE" section. Run the engine while
checking that all systems (raw water pump, oil pressure, battery charging) are functioning.
2.
Start
the
generator and allow the engine to warm up until the water temperature gauge moves into the
130 - 140
0
F range.
3.
Use caution not to overload the generator. The presence
of
a gray or black exhaust with loss
of
engine
rpm (hertz) are signs
of
a possible overload.
4.
Run the generator at
112
of
its rated capacity for the first
10
hours then increase the load to 3/4
of
its
rated capacity. For the remainder
of
the break-in period, the generator may be run
at
different load
intervals.
Breaking-in a new engine basically involves seating the piston rings to the cylinder walls. Excessive oil
consumption and smoky operation indicate that the cylinder walls are scored, which is caused by
overloading the generator during the break-in period.
As indicated above, operate the generator with a moderate load during the
50 hour break-in period. (On
one hand don't baby the engine, but on the other hand, don't abuse it.)
Remote
Starting
Procedure
The remote start panel is the same as the engine-mounted start panel except that it has a green LED light.
When starting
at
a remote location, the green LED lights faintly when the preheat is depressed.
It
will
dim or flicker when the start switch is depressed and the starter cranks the engine.
Once the engine starts
the green LED will glow bright signaling
to
release the start switch in that the starting
of
the generator
may not be audible at the remote start/stop panel location.
A.
When starting the generator set at a remote location, release the START switch when the green
LED lights bright but continue depressing the
PREHEAT switch. After releasing the START switch,
continue holding the
PREHEAT switch until the oil pressure is sufficient to close the oil pressure
safety switch providing the normal B+ path to the fuel run solenoid. This will
be just a few seconds.
B.
After the generator is started and the starter switch is released, the generator's starter will not crank
until someone again operates the
PREHEAT switch first because this switch supplies voltage to the
START switch.
31
WESTERBEKE
GENERATORS
- WESTERBEKE 1
- • Avoid Moving Parts 4
- FOREWORD 6
- 'c~~ 7
- 5 WESTERBEKE GENERATORS 9
- Shut~off 11
- Dimensions 13
- BTD SYSTEM 14
- ELECTRICAL 15
- ACGENERATOR 15
- EMISSION CONTROL SYSTEMS 16
- CAUTION 17
- Lifting 18
- Rigging 18
- I WARNING I 20
- 21
- /Exhaust 21
- ~===14f.;;;1 22
- #037401 23
- Fl...ANGE 23
- WARNING 27
- WESTERBEKE GENERATORS 24 28
- PREHERT 29
- GENERRTOR 29
- I ' 30
- " 31
- JJ.I,.--SHAFT 32
- PREPARATION 33
- STARTING 33
- WESTERBEKE GENERATORS 38
- ~2' 40
- ---'~ 41
- Battery Specification 42
- 0" 43
- :,'( 44
- '''-'j 45
- W SWITCH 46
- Fresh Water Circuit 47
- FUNCTION 48
- MANIFOLD 48
- PRESSURE 48
- REPLACE 50
- SCREWORIVER 51
- "A"nAA'" 52
- I' 53
- ;' 53
- 'l'..J 54
- BT GENERATOR 55
- Securing 56
- : , Btl 57
- Generator Frequency 58
- Load Connections 58
- WESTERBEKE GENERATORS 54 58
- '-1 59
- ~' 60
- An electric motor connected 61
- 59 WESTERBEKE GENERATORS 63
- 3. Check that 64
- * ) are recommended to be 67
- * ) should be performed 68
- A®~f"t4a;::;r 69
- Timing mark 70
- DELIYEiY 71
- DELIVERY 71
- Adjustments (Generator) 72
- Generator 72
- Frequency Adjustment (Hertz) 72
- #037100 73
- #034569 73
- Starter 76
- Cylinder Lubrication 76
- 'U 77
- ± 10/0 kglcm 79
- ± 140/0) 79
- An impeller kit 80
- A starter 80
- ,"' 83
- TII_IlM_ 83
Powiązane produkty i podręczniki dla Silnik Westerbeke 38B FOUR
Silnik Westerbeke M4-30 Instrukcja Właściciela
(74 strony)
(74 strony)
Silnik Westerbeke M-50B Instrukcja Instalacji
(57 strony)
(57 strony)
Silnik Westerbeke 21A Instrukcja Użytkownika
(6 strony)
(6 strony)
Silnik Westerbeke 60 Instrukcja Użytkownika
(10 strony)
(10 strony)
Silnik Westerbeke M-30 Instrukcja Obsługi
(29 strony)
(29 strony)
Silnik Westerbeke 20B TWO Instrukcja Instalacji
(72 strony)
(72 strony)
Silnik Westerbeke 120D-TWO Instrukcja Instalacji
(68 strony)
(68 strony)
Silnik Westerbeke M3-20 Dokumentacja
(52 strony)
(52 strony)
Silnik Westerbeke W-70GA Instrukcja Instalacji
(64 strony)
(64 strony)
Silnik Westerbeke 71 B-FOUR Instrukcja Obsługi
(80 strony)
(80 strony)
Silnik Westerbeke 55A FOUR Instrukcja Instalacji
(44 strony)
(44 strony)
Silnik Westerbeke 65B-FOUR Instrukcja Instalacji
(64 strony)
(64 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji